Dejitter It WiFi X
WiFi adapted for high end audio - WiFi X
The system comes complete and ready to plug in and use. No config required
It is best used with the Switch X for a complete clean networking solution
WiFi is used in audio systems to control a music server and most audiophiles have a WiFi access point or Wifi Router close to audio gear. Control of a audio server is a very low speed application. The iPad will also be be used in the same room
WiFi access points / WIFi routers are engineered to be as fast as possible and as powerful as possible to cover a whole house. This is VERY bad for use around audio gear blasting WIFi energy out at the highest legal power with the widest channel for distance and speed. Audio Interconnects and gear can pick this up and it can cause issues. The high power WiFi will saturate audio interconnects and get into gear that is close to the access point or WiFi router. RFI & WiFi will travel down the ethernet or power wires and get into audio gear which is typically connected with wire ethernet connections and a network switch
WiFi for audio use is a different animal. It should not radiate excessive power and it should be a narrow wifi channel which is far less overall channel power and much better at maintaining a clean solid connection
The WiFi from the unit is not like any other access point because it targets a very specific application. It is also fully compliant with all standards and works with everything that can work on a 5Ghz band.
This all resulted in a stunning drop in radiated WiFi energy getting into/onto audio system interconnects and gear.
The modified Aruba is combined with the DeJitter IT noise canceling linear power supply and a specific cable to match the impedance of the power system in the Aruba.
The Aruba radiates no RF I can measure below 10Mhz which is critical around audio gear and has a VERY clean WiFi signal without any out of band spurious radiation
If you are interested in the WiFi X, please contact us HERE
WiFi adapted for high end audio - WiFi X
The system comes complete and ready to plug in and use. No config required
It is best used with the Switch X for a complete clean networking solution
WiFi is used in audio systems to control a music server and most audiophiles have a WiFi access point or Wifi Router close to audio gear. Control of a audio server is a very low speed application. The iPad will also be be used in the same room
WiFi access points / WIFi routers are engineered to be as fast as possible and as powerful as possible to cover a whole house. This is VERY bad for use around audio gear blasting WIFi energy out at the highest legal power with the widest channel for distance and speed. Audio Interconnects and gear can pick this up and it can cause issues. The high power WiFi will saturate audio interconnects and get into gear that is close to the access point or WiFi router. RFI & WiFi will travel down the ethernet or power wires and get into audio gear which is typically connected with wire ethernet connections and a network switch
WiFi for audio use is a different animal. It should not radiate excessive power and it should be a narrow wifi channel which is far less overall channel power and much better at maintaining a clean solid connection
The WiFi from the unit is not like any other access point because it targets a very specific application. It is also fully compliant with all standards and works with everything that can work on a 5Ghz band.
This all resulted in a stunning drop in radiated WiFi energy getting into/onto audio system interconnects and gear.
The modified Aruba is combined with the DeJitter IT noise canceling linear power supply and a specific cable to match the impedance of the power system in the Aruba.
The Aruba radiates no RF I can measure below 10Mhz which is critical around audio gear and has a VERY clean WiFi signal without any out of band spurious radiation
If you are interested in the WiFi X, please contact us HERE
WiFi adapted for high end audio - WiFi X
The system comes complete and ready to plug in and use. No config required
It is best used with the Switch X for a complete clean networking solution
WiFi is used in audio systems to control a music server and most audiophiles have a WiFi access point or Wifi Router close to audio gear. Control of a audio server is a very low speed application. The iPad will also be be used in the same room
WiFi access points / WIFi routers are engineered to be as fast as possible and as powerful as possible to cover a whole house. This is VERY bad for use around audio gear blasting WIFi energy out at the highest legal power with the widest channel for distance and speed. Audio Interconnects and gear can pick this up and it can cause issues. The high power WiFi will saturate audio interconnects and get into gear that is close to the access point or WiFi router. RFI & WiFi will travel down the ethernet or power wires and get into audio gear which is typically connected with wire ethernet connections and a network switch
WiFi for audio use is a different animal. It should not radiate excessive power and it should be a narrow wifi channel which is far less overall channel power and much better at maintaining a clean solid connection
The WiFi from the unit is not like any other access point because it targets a very specific application. It is also fully compliant with all standards and works with everything that can work on a 5Ghz band.
This all resulted in a stunning drop in radiated WiFi energy getting into/onto audio system interconnects and gear.
The modified Aruba is combined with the DeJitter IT noise canceling linear power supply and a specific cable to match the impedance of the power system in the Aruba.
The Aruba radiates no RF I can measure below 10Mhz which is critical around audio gear and has a VERY clean WiFi signal without any out of band spurious radiation
